收藏本站
BD6142AMUV
Datasheet
● Operational Notes
(1) Absolute Maximum Ratings
An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc.,
can break down devices, thus making impossible to identify breaking mode such as a short circuit or an open circuit. If
any special mode exceeding the absolute maximum ratings is assumed, consideration should be given to take physical
safety measures including the use of fuses, etc.
(2) Operating conditions
These conditions represent a range within which characteristics can be provided approximately as expected. The
electrical characteristics are guaranteed under the conditions of each parameter.
(3) Reverse connection of power supply connector
The reverse connection of power supply connector can break down ICs. Take protective measures against the
breakdown due to the reverse connection, such as mounting an external diode between the power supply and the IC’s
power supply terminal.
(4) Power supply line
Design PCB pattern to provide low impedance for the wiring between the power supply and the GND lines. In this
regard, for the digital block power supply and the analog block power supply, even though these power supplies has
the same level of potential, separate the power supply pattern for the digital block from that for the analog block, thus
suppressing the diffraction of digital noises to the analog block power supply resulting from impedance common to the
wiring patterns. For the GND line, give consideration to design the patterns in a similar manner.
Furthermore, for all power supply terminals to ICs, mount a capacitor between the power supply and the GND terminal.
At the same time, in order to use an electrolytic capacitor, thoroughly check to be sure the characteristics of the
capacitor to be used present no problem including the occurrence of capacity dropout at a low temperature, thus
determining the constant.
(5) GND voltage
Make setting of the potential of the GND terminal so that it will be maintained at the minimum in any operating state.
Furthermore, check to be sure no terminals are at a potential lower than the GND voltage including an actual electric transient.
(6) Short circuit between terminals and erroneous mounting
In order to mount ICs on a set PCB, pay thorough attention to the direction and offset of the ICs. Erroneous mounting
can break down the ICs. Furthermore, if a short circuit occurs due to foreign matters entering between terminals or
between the terminal and the power supply or the GND terminal, the ICs can break down.
(7) Operation in strong electromagnetic field
Be noted that using ICs in the strong electromagnetic field can malfunction them.
(8) Inspection with set PCB
On the inspection with the set PCB, if a capacitor is connected to a low-impedance IC terminal, the IC can suffer stress.
Therefore, be sure to discharge from the set PCB by each process. Furthermore, in order to mount or dismount the set
PCB to/from the jig for the inspection process, be sure to turn OFF the power supply and then mount the set PCB to
the jig. After the completion of the inspection, be sure to turn OFF the power supply and then dismount it from the jig. In
addition, for protection against static electricity, establish a ground for the assembly process and pay thorough attention
to the transportation and the storage of the set PCB.
(9) Input terminals
In terms of the construction of IC, parasitic elements are inevitably formed in relation to potential. The operation of the
parasitic element can cause interference with circuit operation, thus resulting in a malfunction and then breakdown of
the input terminal. Therefore, pay thorough attention not to handle the input terminals, such as to apply to the input
terminals a voltage lower than the GND respectively, so that any parasitic element will operate. Furthermore, do not
apply a voltage to the input terminals when no power supply voltage is applied to the IC. In addition, even if the power
supply voltage is applied, apply to the input terminals a voltage lower than the power supply voltage or within the
guaranteed value of electrical characteristics.
(10) Ground wiring pattern
If small-signal GND and large-current GND are provided, It will be recommended to separate the large-current GND
pattern from the small-signal GND pattern and establish a single ground at the reference point of the set PCB so that
resistance to the wiring pattern and voltage fluctuations due to a large current will cause no fluctuations in voltages of
the small-signal GND. Pay attention not to cause fluctuations in the GND wiring pattern of external parts as well.
www.rohm.com
? 2011 ROHM Co., Ltd. All rights reserved.
TSZ22111 ? 15 ? 001
27/30
TSZ02201-0G3G0C400340-1-2
03.Dec.2012 Rev.001
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
BD6581GU-E2 IC LED DVR WHT BCKLGHT VCSP85H2
BD6583MUV-AE2 IC LED DRIVER WHIT BCKLGT 24VQFN
BD6586MUV-E2 IC LED DRVR WHITE BCKLGT 24-VQFN
BD6592MUV-E2 IC LED DRVR WHITE BCKLGT 24-VQFN
BD7844AEFV-E2 IC LED DISPLAY DVR 5V 28-HTSSOP
BD8105FV-E2 IC LED DVR SERIAL PAR 20-SSOP
BD8112EFV-ME2 IC LED DRIVER 24-VSSOP
BD8119FM-ME2 IC WHITE LED DVR PWM 28-HSOP
相关代理商/技术参数
BD615 制造商:INFINEON 制造商全称:Infineon Technologies AG 功能描述:PNP SILICON EPIBASE TRANSISTORS
BD6150CS 制造商:PANJIT 制造商全称:Pan Jit International Inc. 功能描述:SURFACE MOUNT SCHOTTKY BARRIER RECTIFIERS
BD6150CT 制造商:PANJIT 制造商全称:Pan Jit International Inc. 功能描述:SURFACE MOUNT SCHOTTKY BARRIER RECTIFIERS
BD6150MUV 制造商:ROHM 制造商全称:Rohm 功能描述:White Backlight LED Driver for Medium to Large LCD Panels (Switching Regulator Type)
BD6150MUV_11 制造商:ROHM 制造商全称:Rohm 功能描述:White Backlight LED Driver for Medium to Large LCD Panels (Switching Regulator Type)
BD6150MUV-E2 制造商:ROHM Semiconductor 功能描述:CONV DC-DC SINGLE STEP UP 4.2V TO 26V 24-PIN VQFN EP T/R - Tape and Reel 制造商:ROHM Semiconductor 功能描述:IC WHITE LED DVR BKLT 24-VQFN 制造商:ROHM Semiconductor 功能描述:CONV DCDC SNGL STPDN 2V-26V 24PIN 制造商:ROHM Semiconductor 功能描述:White Backlight LED Driver,106 LED,30mA
BD6155FVM 制造商:ROHM 制造商全称:Rohm 功能描述:DC/DC converter for LCD back light
BD6155FVM-E2 功能描述:IC LED DRIVR WHITE BCKLGT 8-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND